If you are often facing a situation of dead car batteries, you might not be probably jumpstarting your car battery just the right way. Replacing your car battery might be very costly. Take a look at car battery prices Brisbane from Roadside Response and you will get an idea. In such a situation, it’s good to know how to jumpstart your car battery the right way. The professionals from Roadside Response are happy to guide us here on this very topic.

Getting the Appropriate Jumper Cables

If you are under an impression that you will need a lot of tools to jump your car battery, you are wrong. To start with, find a functioning car for using for the jumpstart. Ensure that both the car owners are fine with opening the hood and locating the battery as well as battery terminals. The most popular tool to jumpstart cars are jumper cables, since they are low-priced and easy to store. Jumper cables are often available in various lengths and range from 10 to 20 feet. Many people consider long cables better because you need not move a car having a dead battery. However, though longer cables seem convenient, they may lose power, since the longer the cable, the farther the energy needs to travel. The cables’ strength is denoted by the gauge. The lower the gauge, the thicker and stronger are the cables.

Image Courtesy: sstire.com

Safety is of Prime Importance

Before undertaking any basic repair or maintenance task on your car, you should first think upon any safety risks.

  • To start with, ensure that children are at a safe distance from the engine while you are trying to jumpstart a dead car battery.
  • Read your car’s manual.
  • Some cars need additional steps so as to have a successful jump.
  • If you are not sure of what to do, contact a professional for advice.
  • Considering that your vehicle will permit a jump, you should take care of preventing electric shocks.
  • While handling jumper cables, remember that their job is to pass electric current from one vehicle to another. Once one of the ends of the jumper cables is connected to a vehicle, don’t connect the metal clamps to anything else but the correct target.
  • Also take care of wearing protective glasses to beware of sparks flying in air.

Jumping a Car Battery

Preparing for the jump:

  • Park the functional vehicles in such a way that both the cars will face each other, with only around 18 inches between them, but not touching one another. For automatic transmission, put the car in park, while for manual transmission, set it to neutral.
  • Set the parking brakes on the cars, to avoid their unexpected moving.
  • Both the vehicles must be turned off with keys removed.
  • Open the hoods and locate the batteries (check the owner’s manual) and battery terminals. Normally, the terminals on every battery will be black or red with a + or – sign on its top. Make sure that you know which one is positive and which one is negative. This identification is important for a successful jump. Remember to wipe off any dirt from the terminals.

Start Connecting Jumper Cables

  • Connect the positive red cable clamp to the + (positive) terminal of the dead battery. The connection to the battery terminal should be solid which may need some initial wiggling of the clamps.
  • Connect the positive red cable clamp on the other side of the jumper cables to the + (positive) battery terminal of the functioning car.
  • Attach the negative, black cable clamp to the negative (-) terminal of the working battery. But don’t attach the negative black cable clamp to the dead battery. Instead of that, connect that clamp to an unpainted metal part of the vehicle, such as a clean, shiny nut. This will ensure a safe jump.

Jumpstarting

  • Start the functioning car
  • Wait for a moment or two. Based on the age of the battery and since how long it is dead, you may require to allow the car to run for a couple of minutes to have the jump to work.
  • Try starting the vehicle with the dead battery. If it doesn’t start, let the working car charge the battery for an extra minute or two before trying again. In some cases, revving the engine of the functional vehicle slightly while charging the failed battery may help.
  • When the dead vehicle starts running, you can take out the jumper cables. Start with the negative, black cable clamps. Don’t allow the clamps to touch each other while any of the cables’ parts are still connected to the car.
  • Take a short drive which will enable the battery to develop a charge and ensure that your car doesn’t die again after you turn it off.

Roadside Response Brisbane provides 24/7 roadside assistance across Australia within 50 minutes. Visit their site to know more about their exceptional services.